Don't dream, do!
Chris Wetmore posted an answer for this Brother Sewing Machines:
"I would suggest by the time the quilt rolls up on the frame the machine would have too..."
Chris Wetmore posted an answer for this Husqvarna Sewing Machines:
"The button is on the top left of your machine, near the take up lever. Push down to..."
Chris Wetmore posted an answer for this Baby Lock Sewing Machines:
"Palette 5.0 is no longer supported (Sadly) I have 6.0 and the same challenge. I now have..."
Chris Wetmore posted an answer for this Sewing Machines:
"This sounds like the X or Y encoders are not telling the machine to stitch when it moves. ..."
Chris Wetmore posted an answer for this Baby Lock Sewing Machines:
"In the embrilliance software check the hoops size. Dst files do not save hoop size in the..."
Chris Wetmore posted an answer for this Janome Sewist 525S Mechanical Sewing Machine:
"Hello Emma, Hope this helps. When the feed dogs are lowered they will not go up with just..."
Chris Wetmore posted an answer for this Baby Lock Ellure:
"The board XA3592008 (usa) part number contains the LCD backlights. if you can find this..."
Chris Wetmore posted an answer for this Baby Lock Esante:
"I have not yet seen babylock release a driver for windows 8 and the BLN. The dealer..."
Chris Wetmore posted an answer for this Baby Lock Esante:
"1. Turn the power on while holding down the [Start/Stop], [Reverse stitch], and [Needle..."
Chris Wetmore posted an answer for this Sewing Machines:
"This sounds like too much presser foot pressure. You can reduce the pressure on the foot..."
Chris Wetmore posted an answer for this Baby Lock Sewing Machines:
"Try here http://babylock.com/ftp/whitepapers/EclipseDX_BLE1DX-2_InstRefGuidepdf.pdf this..."
Chris Wetmore posted an answer for this Consew Sewing Machines:
"Did you try Resources You could also email them at [email protected]"
Chris Wetmore posted an answer for this Elna Sewing Machines:
"I have this manual, email me chrisatcentralsewingdotcom and I will send it to you (pdf)..."
Chris Wetmore posted an answer for this Brother PE770 Computerized Sewing Machine:
"this is a 4"x 4" sewing field."
Chris Wetmore posted an answer for this Brother LB6770 PRW Computerized Sewing Machine:
"Yes. It is a sensor on the take up spring. If you miss threading the take up spring you..."
Chris Wetmore posted an answer for this Brother PC-420:
"This sounds like a bushing is seized or thread wrapped on the machine somewhere."
Chris Wetmore posted an answer for this Brother Sewing Machines:
"Loosen your top tension until bobbin thread disappears fro view on top."
Chris Wetmore posted an answer for this Brother LS-1217 Mechanical Sewing Machine:
"No that is not a walking foot machine. There are no industrial walking feet that will..."
Chris Wetmore posted an answer for this Brother Sewing Machines:
"class 15 or part number 2518 or 2518P for the plastic one."
Chris Wetmore posted an answer for this Brother Sewing Machines:
"I have a PDF of this manual I can email. chris at centralsewing dot com."
Chris Wetmore posted an answer for this Brother SE-400 Sewing & Embroidery Machine:
"Yes they should unless the tab on the middle of the embroidery unit is broken."
Chris Wetmore posted an answer for this Brother Sewing Machines:
"I have this manual, email me chrisatcentralsewingdotcom and tell me in the email what..."
Chris Wetmore posted an answer for this Brother Sewing Machines:
"This is an error generated by an overcurrent on the motor. does the machine turn freely..."
Chris Wetmore posted an answer for this Juki Sewing Machines:
"I have this book. Email Me at chrisatcentralsewingdotcom or use this link..."
Chris Wetmore posted an answer for this Singer Sewing Machines:
"Most singer manuals are available here Instruction Manuals"
Chris Wetmore posted an answer for this New Home Sewing Machines:
"this should be the right one..."
Chris Wetmore posted an answer for this Singer Sewing Machines:
"it is available here Instruction Manuals"
Chris Wetmore posted an answer for this Husqvarna Sewing Machines:
"1. the twin needle button is turned on ( good news). (not sure if this is a function on..."
Chris Wetmore posted an answer for this Husqvarna Huskylock Computerized 910:
"This sounds like a bushing in your serger or the upper looper shaft heats up with use...."
Chris Wetmore posted an answer for this Husqvarna Sewing Machines:
"The machine is actually a brother PE series embroidery machine, no longer supported by..."
Chris Wetmore posted an answer for this Husqvarna Sewing Machines:
"un thread your needles before threading the Lower looper. thread lower looper, then thread..."