Super tech to the rescue.
maxxratt posted an answer for this Hotpoint Dishwashers:
"When you say it won't start, do you mean a) the display is on and it won't respond, or b)..."
maxxratt posted an answer for this Science & Laboratory:
"What is the alarm? What phase of the cycle are you getting your alarm?"
maxxratt posted an answer for this Science & Laboratory:
"What is your question?"
maxxratt posted an answer for this ESCHMANN Little Sister Autoclave Tabletop:
"This is a power failure alarm, meaning the prior cycle failed due to a power failure/..."
maxxratt posted an answer for this Bermad MT Series Automatic Batch Meter:
"Might be a faulty switch. Is the water pressure too high or too low? Verify and adjust..."
maxxratt posted an answer for this Science & Laboratory:
"What errors? More info needed."
maxxratt posted an answer for this MTN Gearsmith New 1500w Commercial Industrial 20l Autoclave High Pressure Steam Sterilizer Tattoo Dental:
"Is it filled with water? If yes, then the liquid level sensor has failed in the unit. This..."
maxxratt posted an answer for this Science & Laboratory:
"What exactly is wrong that you need help with? More info needed. Why was it turned off?..."
maxxratt posted an answer for this ESCHMANN Little Sister Autoclave Tabletop:
"Might be several things. First though, verify that your power outlet can provide enough..."
maxxratt posted an answer for this ESCHMANN Little Sister Autoclave Tabletop:
"Error 3 is a Door lock error and has nothing to do with the water sensor. Tighten the door..."
maxxratt posted an answer for this Tuttnauer EZ10 Automatic Sterilizer/Autoclave with Printer:
"Message is displayed and sterilization does not start if the autoclave has not reached..."
maxxratt posted an answer for this Science & Laboratory:
"More info needed. What happened before it wouldn't turn on. Is it plugged in ( stupid..."
maxxratt posted an answer for this Science & Laboratory:
"Visually check for obstructions on the door seal area. Clean gasket and its mating face...."
maxxratt posted an answer for this Science & Laboratory:
"Further info needed. Do you have a Model and serial number?"
maxxratt posted an answer for this Science & Laboratory:
"It means it was unable to achieve sufficient vacuum to hit whatever set point you have it..."
maxxratt posted an answer for this Science & Laboratory:
"117 degree's F or C? If set to Fahrenheit then that's about right. If set to centigrade..."
maxxratt posted an answer for this SciCan Bravo 21V chamber autoclave with Printer:
"This is a case when you should get a certified technician in on it. It sounds like you..."
maxxratt posted an answer for this Audio Players & Recorders:
"If you read what's in Fixya before posting you would've found this: Posted by: jessy ..."
maxxratt posted an answer for this 2001 Ford Taurus:
"Battery still works meaning you have lights that go on inside? That mean you have a little..."
maxxratt posted an answer for this GE 24 in. Profile PDW7800 Built-in Dishwasher:
"You can't access it from the cleaning chamber. It is on the bottom of the unit, so you'll..."
maxxratt posted an answer for this Refrigerators:
"Sounds like a temperature control module issue. If you have a little time, patience and..."
maxxratt posted an answer for this 2001 Yamaha YZF-R1:
"Does the key go in all the way or does it hang up when you put it in? If the key is in..."
maxxratt posted an answer for this 2001 Hyundai Accent:
"Behind the trim panel to the right of the gas petal."
maxxratt posted an answer for this GE 24 in. Profile PDW7800 Built-in Dishwasher:
"Is this washer new or has it been heavily used? Is the bottom of the washer covered with..."
maxxratt posted an answer for this Televison & Video:
"I had the same problem. It was the "Flyback transformer" after they first replaced the..."