Thermal printer sales & support.
Terry Butcher posted an answer for this Datamax DMX E4203 Printer:
"The Media Sensor is not seeing the labels or is not configured for these labels. Check..."
Terry Butcher posted an answer for this Datamax DMX-I-4208 Label Printer:
"If the ribbon is moving right on the I-4208 so far that you aren't getting print on the..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"To view or set the IP Address on a Datamax I-4208, use the Front Control Panel on the..."
Terry Butcher posted an answer for this Datamax DMX-I-4208 Label Printer:
"Go to Printer Properties and verify that you can print a Test Page (from the General Tab)...."
Terry Butcher posted an answer for this Datamax DMX-I-4208 Label Printer:
"Possible ribbon tear causes are: 1. Your Heat setting (Printhead temp) is too high -..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"When printing on less than full width media, the printer has a printhead-leveling cam to..."
Terry Butcher posted an answer for this Datamax M-CLASS DMX-M-4208 Label Printer:
"This older printer is not Plug n Play. Install driver by starting in Control Panel,..."
Terry Butcher posted an answer for this Datamax M-4208 Thermal Label Printer:
"Free Windows Printer drivers for Datamax can be downloaded here: Custom Design Label..."
Terry Butcher posted an answer for this Datamax M-Class 4208 Thermal Label Printer:
"To try to prevent scratches that ruin your thermal printhead, prevent dust from settling..."
Terry Butcher posted an answer for this Datamax E-4203 Printer:
"Free Windows Printer drivers for Datamax can be downloaded here: Custom Design Label..."
Terry Butcher posted an answer for this Datamax I-4308 Thermal Label Printer:
"Hold down the Menu button on the front of the printer for a few seconds and watch for the..."
Terry Butcher posted an answer for this Datamax M-Class M-4208 Printer:
"If streaks are perfectly vertical and always present, probably your printhead is scratched..."
Terry Butcher posted an answer for this Datamax DMX-I-4208 Label Printer:
"Sounds like your printhead is scratched, therefore needs to be replaced."
Terry Butcher posted an answer for this Datamax DMX-I-4212 Label Printer:
"Hold in the Feed button for 4-5 seconds, which causes the printer to attempt to..."
Terry Butcher posted an answer for this Datamax Office Equipment & Supplies:
"Free Windows Printer drivers for Datamax can be downloaded here: Custom Design Label..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"Hold in the Feed button for 4-5 seconds, which causes the printer to attempt to..."
Terry Butcher posted an answer for this Datamax DMX-I-4208 Label Printer:
"Hold in the Feed button for 4-5 seconds, which causes the printer to attempt to..."
Terry Butcher posted an answer for this Datamax M-Class Thermal Printer:
"Free Windows Printer Drivers for Datamax can be downloaded here: Custom Design Label..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"Slide out the Media Sensor (green plastic bar that sticks out over the labels) about 1..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"If the word "VOID" prints, turn the printer off, reboot your computer, turn the printer..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"Remove the metal cover by removing the screws along the bottom left edge and one in the..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"Hold in the Feed button for 4-5 seconds, which causes the printer to attempt to..."
Terry Butcher posted an answer for this Datamax Office Equipment & Supplies:
"Hold down the Menu button on the front of the printer for a few seconds and watch for the..."
Terry Butcher posted an answer for this Datamax Office Equipment & Supplies:
"Hold in the Feed button for 4-5 seconds, which causes the printer to attempt to..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"Grab used roll in your hand, squeeze and pull - the hub will collapse slightly, releasing..."
Terry Butcher posted an answer for this Datamax I-4208 Thermal Label Printer:
"On the I-4208s, press Menu button on front of printer. Go to Print Control. Go to Custom..."
Terry Butcher posted an answer for this Datamax W-Class W-6208 Thermal Label Printer:
"Hold in the Feed button for 4-5 seconds, which causes the printer to attempt to..."
Terry Butcher posted an answer for this Datamax E4205e Thermal Label Printer:
"Free Windows Printer drivers for Datamax can be downloaded here: Custom Design Label..."
Terry Butcher posted an answer for this Datamax M-Class Thermal Printer:
"Hold in the Feed button for 4-5 seconds, which causes the printer to attempt to..."
Terry Butcher posted an answer for this Datamax I-4308 Thermal Label Printer:
"Hold in the Feed button for 4-5 seconds, which causes the printer to attempt to..."